DIRECTIONS FOR USE
Do not apply a broadcast application to interior surfaces of homes.
Do not apply by air.
Do not apply in plant nurseries.
Do not apply this product through any kind of irrigation system.
Not for use on sod farm turf, golf course turf, or grass grown for seed.
Do not water treated area to the point of runoff.
Do not make applications during rain.
Application is prohibited directly into sewers or drains, or to any area like a gutter where drainage to sewers, storm drains, water bodies, or aquatic habitat can occur. Do not allow the product to enter any drain during or after application.
Additional Application Restrictions for Residential Outdoor Surface and Space Sprays:
All outdoor applications must be limited to spot or crack-and-crevice treatments only, except for the following permitted uses:
(1) Treatment to soil or vegetation around structures;
(2) Applications to lawns, turf, and other vegetation;
(3) Applications to building foundations, up to maximum height of 3 feet.
Other than applications to building foundations, all outdoor applications to impervious surfaces such as sidewalks, driveways, patios, porches and structural surfaces (such as windows, doors, and eaves) are limited to spot and crack-and-crevice applications, only.
GENERAL INFORMATION ON THE USE OF THIS PRODUCT
Bisect L controls a wide spectrum of insects and mites on trees, shrubs, foliage plants, non-bearing fruit and nut trees, and flowers in greenhouses, interiorscapes including hotels, shopping malls, office buildings, etc., and outdoor plantscapes, such as around residential dwellings, parks, institutional buildings, recreational areas, athletic fields and home lawns. Non-bearing crops are perennial crops that will not produce a harvestable raw agricultural commodity during the season of application. Bisect L may also be used in feed and food handling establishments, animal confinement facilities, kennels, confined animal feeding operations, livestock premises, and in/around/under structures.
Resistance: Some insects are known to develop resistance to products used repeatedly for control. Because the development of resistance cannot be predicted, the use of this product should conform to resistance management strategies established for the use area. Consult your local or state pest management authorities for details.
If resistance to this product develops in your area, this product, or other products with a similar mode of action, may not provide adequate
If poor performance cannot be attributed to improper application or extreme weather conditions, a resistant strain of insect may be present.
If you experience difficulty with control and suspect that resistance is a reasonable cause, immediately consult your local company representative or pest management advisor for the best alternative method of control for your area.
Do not use household utensils to measure Bisect L.
Note: Higher finished volume should be applied to penetrate thatch, mulch, brush, and porous surfaces. Lower finished volumes can be used indoors and for non-porous surfaces. Do not apply more than 1.0 ounce Bisect L per 1000 square feet.
GENERAL APPLICATION INSTRUCTIONS
Bisect L formulation mixes readily with water and other aqueous carriers.
Bisect L may be tank-mixed with adjuvants, and with other pesticides, including insect growth regulators. When tank mixing Bisect L with other pesticides, observe all precautions and limitations on each separate product label. The physical compatibility of Bisect L may vary with different sources of pesticide products, and local cultural practices. Any tank mixture which has not been previously tested should be prepared on a small scale (pint or quart jar), using the proper proportions of pesticides and water to ensure the physical compatibility of the mixture.
Do not apply a broadcast application to interior surfaces of homes.
Do not apply to pets, food crops, or sources of electricity.
Firewood is not to be burned for 1 month after treatment.
Use only in well ventilated areas.
Do not use on edible crops.
During any application to overhead areas within the structure, cover surfaces below with plastic sheeting or similar material, except for soil surfaces in crawlspaces.
Do not allow spray to contact food, foodstuffs, food contacting surfaces, food utensils or water supplies.
Thoroughly wash dishes and food handling utensils with soap and water if they become contaminated by application of this product.
Do not treat areas where food is exposed.
During indoor surface applications do not allow dripping or run-off to occur.
Do not allow people or pets on treated surfaces until spray has dried.
Let surfaces dry before allowing people and pets to contact surfaces.
Prior to applying Bisect L to wood siding, especially rough wood siding, be sure to thoroughly agitate the tank mixture. Prior to treating wood siding, test a small area and allow it to dry to be sure no deposits will form. Follow the same procedure when applying to wood surfaces in direct sunlight or the heat of the day.
Do not apply this product in patient rooms or in any rooms while occupied by the elderly or infirm.
Do not apply in classrooms when in use.
Do not apply when occupants are present in the immediate area in institutions such as libraries, sports facilities, etc.
Application equipment that delivers low volume treatments, such as the Micro-Injector or Actisol applicators, may also be used to make crack and crevice, deep harborage, spot and general surface treatments of Bisect L.
To control adult mosquitoes outdoors on residential, institutional, public, commercial and industrial buildings, and lawns, ornamentals, parks, recreational areas and athletic fields.
Apply Bisect L for mosquito control at an application rate of 0.33 to 1.0 fluid ounce Bisect L per gallon of water (0.07 to 0.22 pound bifenthrin per acre), and apply at the rate of 1.0 gallon of dilution per 1000 square feet as a general spray (refer to the Bisect L Dilution Chart). Use the high rate for residual control of mosquitoes. Use this product for control of mosquitoes that may potentially transmit malaria, and arboviruses (West Nile fever, Dengue fever, Eastern equine encephalitis, and St. Louis encephalitis.)
Apply as a residual spray to outside surfaces of buildings including but not limited to, exterior siding, foundations, porches, window frames, eaves, patios, garages, refuse dumps, lawns such as grass areas adjacent to or around private homes, duplexes, townhouses, condominiums, house trailers, apartment complexes, carports, fence lines, storage sheds, barns, and other commercial, residential and non-commercial structures, soil, trunk of woody ornamentals, trees, shrubs, ground cover, bedding plants, foliage plants, flowers, nonbearing fruit and nut trees, urban areas, parks, campsites, athletic fields, playgrounds, recreational and overgrown waste areas, roadsides and other areas where mosquitoes are found. May also be applied to non-bearing crops or perennial crops that will not produce harvestable raw agricultural commodities during the season of application.
Use the high rate for heavy pest infestation, quicker knockdown, or longer residual control. Retreatment may be necessary to achieve and/or maintain control during periods of high pest pressure, or if there are signs of renewed insect activity. For the lower use rates, repeat application should be limited to no more than once per 7 days. For the high use rate of 1.0 fluid ounce Bisect L per gallon of water, do not apply more than once per 4 weeks.
Apply with hand-held and back pack sprayers or mist blowers, ground sprayers, power sprayers, truck mounted hydraulic sprayers or mist blowers. Do not apply by air or with hand held or truck mounted cold aerosol ULV sprayers and thermal fogging devices. For best results, apply when the mosquitoes are most active. Application during the cooler hours of the night or early mornings is recommended.
Do not apply more than 1.0 fluid ounce of Bisect L per 1000 square feet (equivalent to 0.22 pound bifenthrin per acre) per application.
Do not apply when wind speed exceeds 10 MPH.