POTATOES - PREEMERGENCE
SOIL TEXTURE: As used on the label, “Coarse soils” are loamy sand or sandy loam soils. “Medium soils” are loam, silt loam, silt, sandy clay, or sandy clay loam. “Fine soils” are silty clay, silty clay loam, clay, or clay loam. Silty clay loam soils are transitional soils and may be classified as medium textured soils in some regions of the U.S.
GENERAL PRECAUTIONS AND RESTRICTIONS
Do not allow sprays to drift on to adjacent desirable plants.
Apply this product only as specified on the label.
Do not use on other crops grown for food or forage.Observe all cautions and limitations on labeling of all products used in mixtures.
For all uses: Low-pressure and high-volume hand-wand equipment is prohibited.
APPLICATION OF METRIBUZIN DF WITH HERBICIDE SPRAY EQUIPMENT
Use a standard low pressure (20 to 40 psi.) herbicide boom sprayer equipped with suitable nozzles and screens no finer than 50-mesh in nozzle and in-line strainers. Agitate thoroughly before and during application with bypass agitation.
GROUND APPLICATION: Apply the proper rate of Metribuzin DF in a minimum of 10 to 40 gallons of spray mixture per acre broadcast.
Banded Application: Use proportionally less Metribuzin DF per acre in a band versus a broadcast application. For band application use 1/4 to 1 gallon of spray mix per inch of band width regardless of row spacing.
EXAMPLES: (1) To treat a 15-inch band on rows 30 inches apart, use one-half of the broadcast rate of Metribuzin. (2) To treat a 14-inch band on rows 42 inches apart, use one-third of the broadcast rate of Metribuzin.
AERIAL APPLICATION: Where permitted, apply specified rate in a minimum of 2 to 10 gallons of spray mixture per acre. Do not apply aerially when wind speed is greater than 10 mph.
NOTE: Do not apply aerially when Metribuzin is tank-mixed with Lasso.
For All Applications of Metribuzin DF: Sprayer must be accurately calibrated before applying Metribuzin DF. Check sprayer during application to be sure it is working properly and delivering a uniform spray pattern. As the volume of spray mixture decreases per acre, the importance of accurate calibration and uniform application increases. Avoid over application, misapplication, and boom and spray swath overlapping that will increase spray dosage. (Crop injury may occur as a result). Avoid spray skips and gaps which allow weeds to grow in untreated soil. Do not apply when weather conditions favor spray drift and/or when sensitive or cool season crops, such as cole crops, onions, peas, or strawberries are present in adjacent fields or in areas where wheat is growing in coarse textured soils.
COMMERCIAL IMPREGNATION AND APPLICATION OF METRIBUZIN DF ON DRY BULK FERTILIZER
Dry bulk fertilizer may be impregnated or coated with Metribuzin DF for application to established alfalfa and to soybeans. All recommendations, cautions, and special precautions on the label must be followed along with state regulations relating to dry bulk fertilizer blending, impregnating and labeling.
APPLICATION: Uniform application is essential for satisfactory weed control. Accurate calibration of fertilizer application equipment is essential for uniform distribution to the soil surface. The recommended method of application is to apply 1/2 the recommended rate and overlap 50 percent or to double apply by splitting the middles to obtain the best distribution pattern.
If fertilizer materials are excessively dusty, use diesel oil or other suitable additive to reduce dust prior to impregnation as dusty fertilizer will result in poor distribution during application. Crop injury and/or poor weed control may occur where the impregnated fertilizer is not uniformly applied.
INCORPORATION AND COMBINATION USES: When Metribuzin DF is to be used in combination with another herbicide, follow directions on the label for combinations, rates, crops, incorporation, and special precautions.
Metribuzin DF herbicide is recommended for use in ground, aircraft or specified chemigation equipment as a pre-emergence and/or postemergence application to potatoes. Early maturing smooth skinned white and all red skinned varieties may be injured with postemergence applications. The varieties Atlantic, Bellchip, Centennial, Chipbelle and Shepody are sensitive to Metribuzin DF. Avoid postemergence applications on these varieties. Pre-emergence applications on these varieties may cause crop injury under adverse weather conditions, on coarse soils, under high soil pH, with higher rates per acre and with mechanical incorporation.
Ground Application: Metribuzin DF is recommended for use with ground spray equipment applied as a pre-emergence and/or postemergence application for control of the listed grass and broadleaf weeds in potatoes. Apply as a uniform broadcast spray at 20 or more gallons per acre.
Aerial Application: Metribuzin DF may be applied in aerial spray equipment as a pre-emergence and/or postemergence application at 5 or more gallons per acre.
Chemigation: Metribuzin DF may be applied pre-emergence and/or early postemergence to potatoes using center pivot, solid set and lateral roll systems. Apply specified dosage in 1/4 to 3/4 inch of water per acre (1/4 to 1/2 inch on sandy soil) as a continuous injection in self-propelled systems or apply in the last 15 to 30 minutes of the set in other systems. Be sure all the Metribuzin DF has been flushed from the lines before shutting down the system.
Metribuzin DF applied to potatoes according to directions, will provide economic control of the following weeds. For optimum control, applications should be made before weeds are 1 inch tall.
SPECIAL PRECAUTIONS (Potatoes):
Do not use Metribuzin DF on potatoes in Kern County, California.
Do not apply more than a total of 1-1/3 lbs Metribuzin DF per acre in a single crop season regardless of the method of application.
Do not make postemergence applications prior to rainfall or irrigation on recently cultivated potatoes, nor within 3 days after periods of cool, wet cloudy weather or injury may occur.
Postemergence applications may cause some chlorosis or minor necrosis. These symptoms may be more severe if seed-piece decay is occurring or if growing conditions favor crop stress.
Postemergence applications may be made only on russet or white skinned varieties that are not early maturing.
Potato varieties may vary in their response to herbicide applications. When using Metribuzin DF for the first time on a particular variety, always determine crop tolerance before using on a field scale.
Do not apply Metribuzin DF within 60 days of harvest.
Do not use air blast sprayers.
Do not apply to sweet potatoes or yams.
Do not plant sensitive crops such as onions, lettuce, cole crops and cucurbits during the next growing season following Metribuzin DF application.
Certain cereal varieties are sensitive to Metribuzin DF (see cereal section of the label for sensitive varieties) and should not be planted during the next growing season unless the following cultural practices occur:
1. Potato vines left in rows as a result of harvest must be uniformly distributed over the soil surface prior to plowing and,
2. Plow with a moldboard plow to a depth sufficient to mix the upper 8 inches of soil.
PREEMERGENCE: Apply specified dosage as a broadcast spray. Do not mechanically incorporate into soil. Use the 1/3 to 2/3 lb/acre rate for control of wild mustard (Brassica sp.) only. On sand soils or sensitive varieties, do not exceed 2/3 lb/acre.