COTTON - MINIMUM/CONSERVATION TILLAGE
Treflan HFP herbicide is a selective herbicide for the preemergence control of annual grasses and broadleaf weeds. Treflan HFP may be applied in liquid sprays of water or liquid fertilizer, or impregnated on dry bulk fertilizer. To reduce loss of herbicidal activity, Treflan HFP should be soil incorporated within 24 hours after application unless otherwise specified in specific use directions or supplemental labeling. Treflan HFP may be tank mixed or followed by overlay or postemergence treatments with other herbicides to improve the spectrum of weeds controlled. Treflan HFP controls weeds by disrupting growth processes during germination. Treflan HFP does not control established weeds.
General Use Precautions
Applied according to directions and under normal growing conditions, Treflan HFP will not harm the treated crop. Over-application may result in crop injury or rotational crop damage from herbicide carryover. Uneven application or improper incorporation of Treflan HFP can result in erratic weed control or crop injury. Seedling disease, cold weather, deep planting, excessive moisture, high salt concentration, or drought may weaken crop seedlings and increase the possibility of damage from Treflan HFP. Under these conditions, delayed crop development or reduced yields may result.
Do not apply Treflan HFP to soils that are wet or are subject to prolonged periods of flooding as poor weed control may result.
Do not use Treflan HFP on any crop grown in Pecos county or Reeves county, Texas.
In Montana, uses of Treflan HFP are limited to those described in supplemental labeling. Refer to supplemental labeling for crops and specific use directions.
General: As spray volume decreases, the importance of accurate calibration and uniform application increases. Check calibration and uniformity of spray application daily. To avoid spray drift, do not apply when winds are gusting or when wind speed is greater than 15 mph.
Ground Broadcast Application
Apply Treflan HFP in 5 to 40 gallons of liquid carrier per acre (broadcast basis), using any properly calibrated, low-pressure herbicide sprayer that will apply the spray uniformly. The carrier may be water or liquid fertilizer as specified for the crop to be treated in the “Approved Crops” section of the label. For band application, adjust herbicide rate and spray volume in proportion to the band width and row width treated.
Aerial Broadcast Application
Apply Treflan HFP in 5 to 10 gallons of water per acre. Adjust pump pressure, nozzle arrangements, speed, and application height to provide uniform application to the soil surface.
Use swath markers or flaggers to assure proper swath width interval.
Preplant Incorporated Application
Treflan HFP may be applied and incorporated prior to planting when soil can be worked and is in a condition that allows thorough mixing to insure uniform incorporation. See “Approved Crops” section for application timing recommendations for specific crops.
Preemergence Application Immediately After Planting
Apply and incorporate Treflan HFP immediately after planting and prior to crop germination. Adjust incorporation equipment so as to avoid disturbance of planted seed. Refer to the “Approved Crops” section of the label for crop specific instructions.
Postemergence and Layby Application
Apply and incorporate Treflan HFP at the recommended rate to the established crop at or before the last cultivation. Required preharvest intervals for treatments with Treflan HFP for certain crops are specified in the “Approved Crops” section of the label. Crop cover may prevent uniform soil coverage from over-the-top sprays. To avoid this problem, use drop nozzles or directed sprays to achieve uniform soil coverage.
Refer to the Supplemental Label for the Directions of the following:
- Treflan HFP Plus Scepter Combinations for Weed Control in Soybeans in the state of California. - Chemigation in Established Plantings of Tree and Vine Crops.
- Coulter caddy for second incorporation of fall applied Treflan HFP.
- Treflan HFP Plus Atrazine Tank Mix for Weed Control in Field Corn in the states of Alabama, Florida, Georgia, and Texas.
- Special Use Program - Control of DNA-Resistant Goosegrass in Soybeans with Treflan HFP Plus Dual Tank Mix.
- Treflan HFP plus Pursuit Combinations for Weed Control in Peanuts.
- Treflan HFP 72 Hour Incorporation Delay in the states of Arizona and California.
- Green Foxtail (Pigeongrass) Resistance to Dinitroaniline Herbicides Including Treflan HFP, Identified in the State of North Dakota.
- Special Use Program - Enhanced Control of Broadleaf Signalgrass in Soybeans with Treflan HFP Plus Dual Tank Mix.
Refer in the label regarding tank mix information.
Minimum Tillage Cotton - Conservation Tillage Cotton
Fall Application Prior to Establishing a Cover Crop
Apply Treflan HFP to flat ground at a broadcast rate of 2.0 to 3.0 pints per acre. Use the 3-pint per acre rate where crop residues are present or where dense weed populations are anticipated. Incorporate once within 24 hours using incorporation implements, such as a springtooth harrow, set to cut no more than 2 to 3 inches deep. Do not incorporate with a tandem disc. Form beds with disc bedders or other bedding implements that will mix and move most of the treated soil from the furrow area to the beds. Fertilizer may be applied as appropriate during incorporation operations. Plant 2 to 4 rows of a small grain cover crop, such as barley, rye or wheat, 2 inches deep in the furrow area between the beds. To avoid injury to small grain seedlings, place seed below the treated layer of soil. Barley is more tolerant to injury than wheat or rye. Existing soil moisture must be present to establish and maintain the cover crop. In late winter (February), apply 2,4-D if necessary for broadleaf weed control.
Restrictions and Use Precautions
Precautions: To avoid crop injury, cotton should be planted after early season adverse weather conditions have passed, especially when using high rates. Cool, wet weather early in the growth cycle causes stress to the cotton plant. The added stress may result in reduced stand, delayed maturity, and reduced yields.
Maximum Crop Year Use Rates: For full season weed control, Treflan HFP may be applied one or more times sequentially during the crop year observing the rates, methods of application, and a 90-day preharvest interval. The maximum dosage must not exceed the rates given, and the maximum cumulative amount of Treflan HFP that may be applied within the same crop year (includes fall application, spring application, and layby application) must not exceed 4.0 pints per acre (2 pounds active ingredient per acre).