COTTON - CONTROL/SUPPRESSION OF EMERGED WEEDS IN ROW MIDDLES - TEXAS

General Information

GENERAL INSTRUCTIONS AND INFORMATION

Do not apply this product through any type of irrigation system.

When Gramoxone Max is applied at less than 10 gallons per acre finished spray volume, a drift control or spray deposition additive SHOULD be used. Refer to the additive label for use directions.

GENERAL INFORMATION

Gramoxone Max is a contact herbicide used to control or suppress a broad spectrum of emerged weeds. Gramoxone Max controls most small annual weeds – both broadleaves and grasses, and suppresses perennial weeds by destroying green foliage. Gramoxone Max can also be used as a desiccant/defoliant at harvest.

Gramoxone Max is formulated as a liquid which contains 3 lbs. of active ingredient per gallon. The formulation contains a nontoxic odor and an emetic (an agent which will induce vomiting if the product is swallowed). The odor is included in the formulation to help prevent accidental ingestion of Gramoxone Max.

Gramoxone Max is rapidly absorbed by green plant tissue and interacts with the photosynthetic process to produce superoxides which destroy the plant cells. Gramoxone Max requires actively growing green plant tissue to function. Thorough coverage of all green foliage is essential for effective weed control and for effective crop desiccation/defoliation. Gramoxone Max is not as effective on drought-stressed weeds, weeds with little green foliage (i.e., mowed or cut weeds), or mature woody bark of trees and vines.

Clay and organic matter rapidly tie up Gramoxone Max. As a result, Gramoxone Max has no residual soil activity to affect later-planted crops or later germinating weeds.

RAINFASTNESS

Because Gramoxone Max is rapidly absorbed by the weed foliage, rain occurring 30 minutes or more after application will have no effect on the activity of Gramoxone Max.

APPLICATION

Since Gramoxone Max is a contact-type herbicide, it is essential to obtain complete coverage of target weeds to get good control. Improper application technique and/or application to large, stressed, or mown weeds will usually result in unacceptable weed control and unacceptable crop desiccation/ defoliation. Complete coverage is also essential for good crop desiccation/defoliation. See details below for specific application instructions.

USE OF A NONIONIC SURFACTANT OR CROP OIL CONCENTRATE

Always add one of the following (Failure to use one of the following at recommended rates will result in reduced performance of Gramoxone Max.)

Nonionic Surfactant: Add nonionic surfactant containing 75% or more surface-active agent at 0.125% v/v (1 pt./100 gals.), OR add a nonionic surfactant containing 50-74% surface-active agent at 0.25% v/v (2 pts./100 gals.), of the finished spray volume for ground applications. For aerial applications, add a nonionic surfactant at 0.25% v/v (2 pts./100 gals.) of the finished spray volume.

Crop Oil Concentrate: Add a nonphytotoxic crop oil concentrate containing 15-20% approved emulsifier, at 1.0% v/v (1 gal./100 gals.) of the finished spray volume for ground applications. For aerial applications, add 1 pt. of crop oil concentrate per acre. Do not use crop oil concentrate when using Gramoxone Max for cotton harvest aid.

GENERAL PRECAUTIONS AND RESTRICTIONS

EQUIPMENT/CONTAINER

Flush all spray equipment with water after use each day. Gramoxone Max is corrosive to aluminum. Aluminum spray equipment and aluminum aircraft structures that are exposed to spray solution or spray drift should be flushed thoroughly with water immediately after use.

In dry areas, dust stirred up by high winds or equipment tires can coat weed or plant leaves and reduce Gramoxone Max activity. Avoid applying Gramoxone Max in extremely dusty conditions.

LIMITATIONS AND PRECAUTIONS

- For Cotton Harvest Aid: Do not pasture livestock in treated fields or feed treated foliage.

- DO NOT use around home gardens, schools, recreational parks, or playgrounds.

- In preplant and preemergence (to the crop) uses, do not apply to soils lacking clay minerals, i.e., peat, muck, pure sand, artificial planting media.

- Seedbeds and plantbeds should be formed as far ahead of planting and treatment as possible to permit maximum weed and grass emergence prior to treatment.

- Seeding or transplanting should be done with a minimum amount of soil disturbance.

- Gramoxone Max used for preplant weed control over the top of plastic mulch may damage transplants which come in contact with the plastic. Sufficient rainfall or sprinkler irrigation to cause wash-off prior to planting may be needed to prevent damage to the crop.

- Weeds and grasses emerging after application of Gramoxone Max will not be controlled or suppressed.

- Unless otherwise indicated, crop plants emerged at time of application may be severely injured or killed if contacted by sprays of Gramoxone Max.

Limitations, Restrictions, and Exceptions

FOR CONTROL OR SUPPRESSION OF EMERGED WEEDS IN ROW MIDDLES IN COTTON

Minimum Total Spray Per Acre: 10 gals.

Use the higher rate on dense populations and/or on larger or hard to control weeds. Apply when weeds are actively growing and between 1\" to 6\" in height. Weeds 6\" or taller may not be controlled. GRAMOXONE MAX may be tankmixed with other registered herbicides for improved burndown and residual control. Refer to the GRAMOXONE MAX federal label for mixing instructions.

ALWAYS ADD THE FOLLOWING:

NONIONIC SURFACTANT: Add nonionic surfactant containing 75% or more surface-active agent at 0.25% v/v (2 pints per 100 gallons), of the finished spray volume for ground applications.

CROP OIL CONCENTRATE: Add a nonphytotoxic crop oil concentrate containing 15-20% approved emulsifier, at 1.0% v/v (1 gallon per 100 gallons) of the finished spray volume for ground applications.

PRECAUTIONS, RESTRICTIONS AND COMMENTS:

- AVOID CONTACT WITH CROP. Intentional or accidental contact (including drift) of GRAMOXONE MAX with the crop may result in severe damage or loss of the crop.

- Apply by directing spray between the rows and using hooded sprayers to prevent spray contact with crop plants.

- Equipment should be in good operating condition. Avoid leakage or dripping onto crop. Variation in equipment design may affect level of weed control.

- Keep hoods adjusted to insure adequate contact with weeds while shielding the crop from the herbicide.

- To minimize drift, do not use nozzles or nozzle configurations, which produce fine spray droplets (mist).

Do not apply this product through any type of irrigation system.

Restricted Entry Interval

12 hours