PEANUTS

General Information

PRODUCT INFORMATION

Micro-Tech herbicide is recommended for control of yellow nutsedge and the annual grasses and broadleaf weeds listed in the “WEEDS CONTROLLED” section of the label. This product may be applied either as a surface application before or after planting or shallowly incorporated prior to planting to blend the herbicide treatment into the upper 1 to 2 inches of soil. The seedbed should be fine, firm and free of clods when tillage is performed.

Precautions and Restrictions

- Rotational crops include: corn (all types), grain sorghum, soybeans, peanuts, dry beans (all types), lima (green), woody ornamentals, cotton, sunflowers, non-grass animal feed crops such as alfalfa, clover, lespedeza, lupin, sainfoin, trefoil, and Vetch spp., cereal grain crops (excluding rice).

- Do not apply more than 4 pounds of alachlor active ingredient per acre per year. This is equivalent to 4 quarts of this product per acre per year.

Read and carefully observe precautionary statements and all other information appearing on the labeling of all products used in mixtures and sequential treatments.

Do not flood irrigate following application of this product or tank-mixtures. This product will not control emerged seedlings.

Do not apply when conditions favor drift.

Use of this product not consistent with the label may result in injury to persons, animals or crops, or other unintended consequences. Keep container closed to prevent spills and contamination.

Flush sprayer with clean water after use.

Applicators should evaluate soil and weed conditions carefully to ensure that they choose the lowest effective label rate.

The use rates of this product and the other herbicides labeled for use in tank-mixtures with this product generally vary with soil texture. Unless soil texture is specifically named, rate tables throughout the label refer to only three soil textural groups: coarse, medium and fine.

APPLICATION INFORMATION

APPLICATION SYSTEMS

Ground Broadcast Treatment—For application into CONVENTIONAL TILLAGE SYSTEMS, apply this product and the labeled tank-mixtures in 15 or more gallons of solution per acre using broadcast boom equipment. For application into CONSERVATION OR MINIMUM TILLAGE SYSTEMS, apply in 10 to 20 gallons of water or 10 to 60 gallons of nitrogen solution per acre when adding Roundup® agricultural herbicides or 2,4-D to the mix. Apply in 20 to 60 gallons of water or nitrogen solution when adding Gramoxone brand herbicides to the mix. The carrier may be either water or sprayable fluid fertilizer as specified for the crop to be treated in the “DIRECTIONS FOR USE” section of the label.

See the Spray Drift Requirements sub-section of the label under the “MIXING, SPRAYING AND HANDLING INSTRUCTIONS” section for additional application requirements.

Band Treatment—Apply a broadcast equivalent rate and volume per acre. Refer to the label to determine the specific rate.

Aerial: Fixed wing, helicopter—Apply this product or approved tank-mixtures in 3 to 10 gallons of water per acre. AVOID DRIFT—DO NOT APPLY DURING INVERSION CONDITIONS, WHEN WINDS ARE GUSTY OR UNDER ANY OTHER CONDITIONS WHICH WILL ALLOW DRIFT.

APPLICATION TIMING AND METHODS

Early Preplant Surface—This product and some labeled tank-mixtures of this product may be applied in no-till and other conservation tillage systems before weeds emerge and up to 45 days before planting certain crops. Split applications can be made 30 to 45 days prior to planting, with 60 percent of the broadcast rate applied initially and the remaining 40 percent applied at planting. Applications made less than 30 days prior to planting can be made either as a split or as a single application. Refer to the individual crop to determine if early preplant application is recommended. If weeds are present at the time of application, apply this product in tank-mixture with an appropriate contact herbicide. Observe directions for use, precautions and restrictions on the label of the contact herbicide. During the planting operation, be careful not to move untreated soil to the surface or move treated soil out of the row, as weed control may be reduced.

Preplant Incorporation—This product and many of the labeled tank-mixtures may be mixed into the soil, using shallow incorporation equipment, any time within 7 days prior to planting. Refer to the crop to be treated in the “DIRECTIONS FOR USE” section of the label to determine if preplant incorporation is recommended. Apply to the soil surface as a broadcast application. Precipitation or irrigation is required to bring incorporated herbicide treatments into contact with germinating weed seedlings. The amount of precipitation or irrigation required depends on existing soil moisture, soil type and percent organic matter content, but 1/3 to 3/4 inch is normally adequate. If weeds emerge after treatment, rotary hoe or shallowly cultivate immediately to improve performance.

NOTE: Do not incorporate unless specifically recommended in the label for the crop and herbicide treatment selected. Incorporation of this product and its labeled tank-mixtures on coarse soil types may reduce length of weed control due to leaching with rainfall or irrigation.

Shallowly incorporate the treatment into the upper 1 to 2 inches of the soil. Equipment should be operated at manufacturer’s designed speed for incorporation to ensure adequate mixing and distribution of the herbicide treatment in the soil. Equipment design, including any drag attachments, must be adequate to avoid soil ridging which may result in streaked or reduced weed control. Equipment should be set to work the soil NO DEEPER THAN 4 INCHES. Soil conditions, including moisture content and crop residue levels, must be suitable to allow thorough and uniform mixing with the equipment used.

Preemergence Surface Application—This product and all labeled tank-mixtures except this product plus Command or Eptam or Treflan may be applied to the soil surface after planting and prior to either crop or weed emergence. Apply within 5 days of last preplant tillage. If weeds emerge after treatment, or if treatment is applied more than 5 days after last preplant tillage, rotary hoe or shallowly cultivate immediately to improve performance.

Precipitation or overhead sprinkler irrigation is required after application to move the herbicide treatment into the weed germination zone. The amount of precipitation or overhead sprinkler irrigation required depends on existing soil moisture, soil type and percent organic matter content, but 1/3 to 3/4 inch is normally adequate. Performance is improved when moisture is received within 7 days after application and prior to weed emergence. High intensity or excessive rainfall or excessive irrigation after application may reduce control.

Postemergence Surface Application—This product and certain tank-mixtures may be applied to specific crops at the ground cracking stage of the crop or after crop emergence. Refer to the specific treatment and crop intended in the “DIRECTIONS FOR USE” section of the label to determine if postemergence applications to the crop are recommended and to determine the proper weed and crop growth stage limitations. Precipitation or overhead sprinkler irrigation is required after application to move the herbicide treatment into the weed germination zone to control unemerged weeds. The amount of precipitation or irrigation required depends on existing soil moisture, soil type and percent organic matter content, but 1/3 to 3/4 inch is normally adequate. If weeds emerge after treatment, rotary hoe or shallowly cultivate immediately to improve performance.

NOTE: Do not apply this product postemergence to corn in Texas.

Cultivation Information—Delay cultivation after application for as long as possible unless weeds or grasses emerge. Shallowly cultivate or rotary hoe immediately if weeds or grasses emerge. If cultivation is necessary because of soil crusting or compaction, set equipment shallow and minimize lateral soil movement to avoid dilution or displacement of the herbicide treatment. If a band application is used and weeds have emerged in the treated band, set cultivator to throw soil into the row, covering the band.

Limitations, Restrictions, and Exceptions

PEANUTS

NOTE: Each crop section of the label provides treatment rates for this product and tank-mixtures including this product. Applications which are not consistent with recommendations in the label may result in unsatisfactory weed control, injury to crops, persons or animals, or other unintended consequences. Refer to specific product labels for crop rotation restrictions and cautionary statements of all products used in these tank-mixtures, including precautions on soil pH, sensitive varieties, minimum re-cropping interval and rotational guidelines.

Use the higher rates in the application rate ranges in areas of heavy weed infestation or where otherwise specified. If emerged weeds exist at planting, the application of a contact herbicide or tillage is recommended when possible to eliminate existing weeds. Do not apply when conditions favor drift.

Detailed information regarding “APPLICATION SYSTEMS” and “APPLICATION TIMING AND METHODS” should be carefully reviewed in conjunction with the information in this section. If the specific information in this section differs from the “PRODUCT INFORMATION”, the specific information should control.

When making applications on peanuts, do not make more than two applications per year or exceed a total of 3 quarts of this product per acre per year.

Do not feed forage or hay from treated crop.

MICRO-TECH

Apply this product in water solution.

APPROVED APPLICATION SYSTEMS

Ground: Broadcast boom, banded; Aerial: Fixed wing, helicopter; Center Pivot Irrigation

APPROVED APPLICATION METHODS

Preplant Incorporated, Preemergence Surface, Ground-crack Surface

Preplant Incorporated—For control of Texas panicum, this application should be made as a tank-mixture with a labeled rate of Prowl or Sonolan DF herbicide.

Ground-crack Surface—Apply this product at the ground-crack stage of peanuts.

Incorporation on coarse soils may result in reduced length of weed control due to leaching with rainfall or irrigation. For improved control of yellow nutsedge and labeled broadleaf weeds, a labeled sequential ground-crack herbicide application should be made.

Restricted Entry Interval

12 hours

Exception: if the product is soil-injected or soil-incorporated, the Worker Protection Standard, under certain circumstances, allows workers to enter the treated area if there will be no contact with anything that has been treated.